Welcome, Guest
Username: Password: Remember me
08 Oct 2017
Well, you've probably noticed by now that things look a little different around here. You are a keen observer!

The whole site is new and that includes all of the software that drives this forum. With probably over 10,000 settings and hundreds of back-end programs trying to talk to one another, there are bound to be a few glitches that we haven't discovered yet. So, if you happen to stumble upon anything that just doesn't seem right, give us a shout and we'll try to sort it out.

Thanks for using the VCOA Forum and enjoy the new look!
  • Page:
  • 1
  • 2

TOPIC: Question Project Yellowbrick

Project Yellowbrick 6 years 2 weeks ago #137

  • brick-a-brac
  • brick-a-brac's Avatar Topic Author
  • Offline
  • Administrator
  • Administrator
  • Posts: 58
  • Thank you received: 5
I've owned my 1972 142E since February of 2007. I bought it from an ad in Turbobricks and had it shipped from its former home in Portland, Oregon. During the course of my ownership, I addressed a number of running issues, but it had one chronic issue -- low compression in #4 cylinder -- that was not going to get better.

So, last year, I had a low-mileage 1969 B20 machined .30 over, balanced, and had an F head shaved to E specs and fitted with double valve springs for the Isky/IPD 7001 cam.


In late May/early June, I gathered up the courage to take the front end apart in preparation for the swap:



A weekend later, the motor was out:


Closer inspection also revealed a very leaky rear main seal, worn clutch, and a bellhousing with shrapnel holes.

Preparation of the engine bay began in late July after I returned from vacation:





In early September, I sprayed the engine compartment with two coats of PPG Delstar acrylic enamel, and tonight, I attached the lightened flywheel, new HD Sachs clutch, and installed the engine:



Stay tuned ...

Please Log in or Create an account to join the conversation.

Re: Project Yellowbrick 5 years 10 months ago #224

  • Walrus3
  • Walrus3's Avatar
  • Offline
  • Fresh Boarder
  • Fresh Boarder
  • Posts: 5
  • Thank you received: 1
Looks great so far. Where does it stand now?

Please Log in or Create an account to join the conversation.

Re: Project Yellowbrick 5 years 10 months ago #225

  • gdill3
  • gdill3's Avatar
  • Offline
  • Moderator
  • Moderator
  • Posts: 1019
  • Karma: 11
  • Thank you received: 87

Walrus3 wrote: Looks great so far. Where does it stand now?


s80.photobucket.com/albums/j170/t5mmmm/?action=view¤t=P1000475.mp4

George Dill

Please Log in or Create an account to join the conversation.

Re: Project Yellowbrick 5 years 10 months ago #226

  • brick-a-brac
  • brick-a-brac's Avatar Topic Author
  • Offline
  • Administrator
  • Administrator
  • Posts: 58
  • Thank you received: 5
Thanks for the assist, George. There is also this:



Essentially, I got the car running, though I ran out of warm weather to put it back together properly. So I slapped the nose back on without the sealer so I could get it into winter storage in time.

In the spring, I plan to put the car back together properly and am shooting to take it to Carlisle in May.

Please Log in or Create an account to join the conversation.

Last Edit: by brick-a-brac.

Re: Project Yellowbrick 5 years 10 months ago #230

  • Walrus3
  • Walrus3's Avatar
  • Offline
  • Fresh Boarder
  • Fresh Boarder
  • Posts: 5
  • Thank you received: 1
Looks good. Have you been in contact with Dave Farrington in RI?
BTW I notice most of your outside pix are taken in the dark - Does the sun not shine where you are?

Please Log in or Create an account to join the conversation.

Last Edit: by Walrus3.

Re: Project Yellowbrick 5 years 10 months ago #232

  • brick-a-brac
  • brick-a-brac's Avatar Topic Author
  • Offline
  • Administrator
  • Administrator
  • Posts: 58
  • Thank you received: 5
It has been getting darker earlier around here ... :laugh:

Most of the work on the car was done after work, so this is the reason for the perpetual darkness.

Please Log in or Create an account to join the conversation.

  • Page:
  • 1
  • 2
  • Not Allowed: to create new topic.
  • Not Allowed: to reply.
  • Not Allowed: to add attachements.
  • Not Allowed: to edit your message.
Time to create page: 0.484 seconds

Please publish modules in offcanvas position.